ABB RDNA-01 Bedienungsanleitung Seite 178
- Seite / 348
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1-174 ACH550-UH User’s Manual
Parameters
8112 LOW FREQ 1 0.0…500.0 Hz 0.1 Hz 30.0 Hz (US)
Sets the frequency limit used to stop the first auxiliary motor. The first auxiliary motor stops if:
• Only one (the first) auxiliary motor is running.
• ACH550 output frequency drops below the limit:
8112 - 1.
• Output frequency stays below the relaxed limit
(8112 + 1 Hz) for at least the time: 8116
AUX MOT STOP D.
After the first auxiliary motor stops:
• Output frequency increases by the value =
(8109 START FREQ 1) - (8112 LOW FREQ 1).
• In effect, the output of the speed regulated motor increases to
compensate for the loss of the auxiliary motor.
See the figure, where:
• A = (8109
START FREQ 1) - (8112 LOW FREQ 1)
• B = Output frequency decrease during the stop delay.
• C = Diagram showing auxiliary motor’s run status as
frequency decreases (1 = On).
• Grey path = Shows hysteresis – if time is reversed, the path
backwards is not the same. For details on the path for
starting, see the diagram at 8109
START FREQ 1.
Note: 8112
LOW FREQ 1 value must be between:
• (2007
MINIMUM FREQ) +1.
• 8109
START FREQ 1
8113 LOW FREQ 2 0.0…500.0 Hz 0.1 Hz 30.0 Hz (US)
Sets the frequency limit used to stop the second auxiliary motor.
• See 8112
LOW FREQ 1 for a complete description of the operation.
The second auxiliary motor stops if:
• Two auxiliary motors are running.
• ACH550 output frequency drops below the limit: 8113 - 1.
• Output frequency stays below the relaxed limit (8113 + 1 Hz) for at least the time: 8116
AUX MOT STOP D.
8114 LOW FREQ 3 0.0…500.0 Hz 0.1 Hz 30.0 Hz (US)
Sets the frequency limit used to stop the third auxiliary motor.
• See 8112
LOW FREQ 1 for a complete description of the operation.
The third auxiliary motor stops if:
• Three auxiliary motors are running.
• ACH550 output frequency drops below the limit: 8114 - 1.
• Output frequency stays below the relaxed limit (8114 + 1 Hz) for at least the time: 8116
AUX MOT STOP D.
8115 AUX MOT START D 0.0…3600.0 s 0.1 s 5.0 s
Sets the Start Delay for the auxiliary motors.
• The output frequency must remain above the start frequency limit (parameter 8109, 8110, or 8111) for this time
period before the auxiliary motor starts.
• See 8109
START FREQ 1 for a complete description of the operation.
8116 AUX MOT STOP D 0.0…3600.0 s 0.1 s 3.0 s
Sets the Stop Delay for the auxiliary motors.
• The output frequency must remain below the low frequency limit (parameter 8112, 8113, or 8114) for this time
period before the auxiliary motor stops.
• See 8112
LOW FREQ 1 for a complete description of the operation.
Group 81: PFA Control
Code Description Range Resolution Default S
t
t
f (Hz)
f
MIN
f
MAX
P 8116
(P 8112)-1
B
1
0
C
P 8112
P 8109
A
A
- …550 HP) 1
- …400 HP) 1
- List of related manuals 2
- Manual contents 3
- ACH550-UH HVAC Drives 5
- 1…550 HP 5
- User’s Manual 5
- Use of warnings and notes 7
- 1-4 ACH550-UH User’s Manual 8
- 1-6 ACH550-UH User’s Manual 10
- Table of contents 10
- ACH550-UH User’s Manual 1-7 11
- 1-8 ACH550-UH User’s Manual 12
- Installation 13
- Preparing for installation 14
- ACH550-UH User’s Manual 1-11 15
- ACH550-UH-08A8-4+ 15
- 1-12 ACH550-UH User’s Manual 16
- Installing the drive 17
- 1-14 ACH550-UH User’s Manual 18
- ACH550-UH User’s Manual 1-15 19
- 1-16 ACH550-UH User’s Manual 20
- ACH550-UH User’s Manual 1-17 21
- 1-18 ACH550-UH User’s Manual 22
- ACH550-UH User’s Manual 1-19 23
- 1-20 ACH550-UH User’s Manual 24
- R5 and R6 25
- 1-22 ACH550-UH User’s Manual 26
- ACH550-UH User’s Manual 1-23 27
- 1-24 ACH550-UH User’s Manual 28
- ACH550-UH User’s Manual 1-25 29
- 1-26 ACH550-UH User’s Manual 30
- ACH550-UH User’s Manual 1-27 31
- 1-28 ACH550-UH User’s Manual 32
- ACH550-UH User’s Manual 1-29 33
- 1-30 ACH550-UH User’s Manual 34
- ACH550-UH User’s Manual 1-31 35
- 1-32 ACH550-UH User’s Manual 36
- HVAC control panel modes 38
- ACH550-UH User’s Manual 1-35 39
- 1-36 ACH550-UH User’s Manual 40
- ACH550-UH User’s Manual 1-37 41
- Changed Parameters Mode 42
- ACH550-UH User’s Manual 1-39 43
- 1-42 ACH550-UH User’s Manual 46
- ACH550-UH User’s Manual 1-43 47
- 1-44 ACH550-UH User’s Manual 48
- ACH550-UH User’s Manual 1-45 49
- I/O Settings Mode 50
- Start-up 51
- 1-48 ACH550-UH User’s Manual 52
- Application macros 53
- 1-50 ACH550-UH User’s Manual 54
- HVAC Default macro 55
- Supply Fan macro 56
- Return Fan macro 57
- Cooling Tower Fan macro 58
- Condenser macro 59
- Booster Pump macro 60
- Pump Alternation macro 61
- Internal Timer macro 62
- ACH550-UH User’s Manual 1-59 63
- Floating Point macro 64
- Dual Setpoint with PID macro 65
- 1-62 ACH550-UH User’s Manual 66
- E-bypass macro 67
- Hand Control macro 68
- E-Clipse macro 69
- 1-66 ACH550-UH User’s Manual 70
- 1-68 ACH550-UH User’s Manual 72
- ACH550-UH User’s Manual 1-69 73
- 1-70 ACH550-UH User’s Manual 74
- ACH550-UH User’s Manual 1-71 75
- 1-72 ACH550-UH User’s Manual 76
- ACH550-UH User’s Manual 1-73 77
- 1-74 ACH550-UH User’s Manual 78
- ACH550-UH User’s Manual 1-75 79
- 1-76 ACH550-UH User’s Manual 80
- ACH550-UH User’s Manual 1-77 81
- 1-78 ACH550-UH User’s Manual 82
- ACH550-UH User’s Manual 1-79 83
- 1-80 ACH550-UH User’s Manual 84
- ACH550-UH User’s Manual 1-81 85
- Group 01: OPERATING DATA 86
- ACH550-UH User’s Manual 1-83 87
- 1-84 ACH550-UH User’s Manual 88
- ACH550-UH User’s Manual 1-85 89
- 1-86 ACH550-UH User’s Manual 90
- Group 03: ACTUAL SIGNALS 91
- 1-88 ACH550-UH User’s Manual 92
- ACH550-UH User’s Manual 1-89 93
- 1-90 ACH550-UH User’s Manual 94
- Group 04: FAULT HISTORY 95
- 1-92 ACH550-UH User’s Manual 96
- ACH550-UH User’s Manual 1-93 97
- Group 11: REFERENCE SELECT 98
- This group defines: 98
- 1 and REF2 98
- ACH550-UH User’s Manual 1-95 99
- 1-96 ACH550-UH User’s Manual 100
- Parameters 100
- ACH550-UH User’s Manual 1-97 101
- 1-98 ACH550-UH User’s Manual 102
- ACH550-UH User’s Manual 1-99 103
- 1-100 ACH550-UH User’s Manual 104
- ACH550-UH User’s Manual 1-101 105
- Group 13: ANALOG INPUTS 106
- Group 14: RELAY OUTPUTS 107
- 1-104 ACH550-UH User’s Manual 108
- ACH550-UH User’s Manual 1-105 109
- 1-106 ACH550-UH User’s Manual 110
- ACH550-UH User’s Manual 1-107 111
- Group 16: SYSTEM CONTROLS 112
- ACH550-UH User’s Manual 1-109 113
- 1-110 ACH550-UH User’s Manual 114
- ACH550-UH User’s Manual 1-111 115
- 1-112 ACH550-UH User’s Manual 116
- ACH550-UH User’s Manual 1-113 117
- 1-114 ACH550-UH User’s Manual 118
- Group 20: LIMITS 119
- 1-116 ACH550-UH User’s Manual 120
- ACH550-UH User’s Manual 1-117 121
- Group 21: START/STOP 122
- ACH550-UH User’s Manual 1-119 123
- 1-120 ACH550-UH User’s Manual 124
- Group 22: ACCEL/DECEL 125
- 1-122 ACH550-UH User’s Manual 126
- Group 23: SPEED CONTROL 127
- 1-124 ACH550-UH User’s Manual 128
- 0, 1 1 0 (OFF) 129
- Group 26: MOTOR CONTROL 130
- ACH550-UH User’s Manual 1-127 131
- Group 29: MAINTENANCE TRIG 132
- Group 30: FAULT FUNCTIONS 133
- 1-130 ACH550-UH User’s Manual 134
- ACH550-UH User’s Manual 1-131 135
- 1-132 ACH550-UH User’s Manual 136
- Group 31: AUTOMATIC RESET 137
- 1-134 ACH550-UH User’s Manual 138
- Group 32: SUPERVISION 139
- 1-136 ACH550-UH User’s Manual 140
- Group 33: INFORMATION 141
- Group 34: PANEL DISPLAY 142
- ACH550-UH User’s Manual 1-139 143
- 1-140 ACH550-UH User’s Manual 144
- ACH550-UH User’s Manual 1-141 145
- FAULT FUNCTIONS 146
- ACH550-UH User’s Manual 1-143 147
- 1-144 ACH550-UH User’s Manual 148
- ACH550-UH User’s Manual 1-145 149
- 1-146 ACH550-UH User’s Manual 150
- ACH550-UH User’s Manual 1-147 151
- Group 37: USER LOAD CURVE 152
- ACH550-UH User’s Manual 1-149 153
- 1-150 ACH550-UH User’s Manual 154
- ACH550-UH User’s Manual 1-151 155
- 1-152 ACH550-UH User’s Manual 156
- ACH550-UH User’s Manual 1-153 157
- 1-154 ACH550-UH User’s Manual 158
- ACH550-UH User’s Manual 1-155 159
- 1-156 ACH550-UH User’s Manual 160
- ACH550-UH User’s Manual 1-157 161
- 1-158 ACH550-UH User’s Manual 162
- ACH550-UH User’s Manual 1-159 163
- Group 41: PROCESS PID SET 2 164
- 1 PARAM SET 164
- ACH550-UH User’s Manual 1-161 165
- 1-162 ACH550-UH User’s Manual 166
- ACH550-UH User’s Manual 1-163 167
- Group 51: EXT COMM MODULE 168
- ACH550-UH User’s Manual 1-165 169
- Group 52: PANEL COMM 170
- Group 53: EFB PROTOCOL 171
- 1-168 ACH550-UH User’s Manual 172
- ACH550-UH User’s Manual 1-169 173
- 1-170 ACH550-UH User’s Manual 174
- ACH550-UH User’s Manual 1-171 175
- 1-172 ACH550-UH User’s Manual 176
- ACH550-UH User’s Manual 1-173 177
- 1-174 ACH550-UH User’s Manual 178
- ACH550-UH User’s Manual 1-175 179
- 1-176 ACH550-UH User’s Manual 180
- ACH550-UH User’s Manual 1-177 181
- 1-178 ACH550-UH User’s Manual 182
- ACH550-UH User’s Manual 1-179 183
- 1-180 ACH550-UH User’s Manual 184
- ACH550-UH User’s Manual 1-181 185
- 1-182 ACH550-UH User’s Manual 186
- ACH550-UH User’s Manual 1-183 187
- 1-184 ACH550-UH User’s Manual 188
- Group 98: OPTIONS 189
- 1-186 ACH550-UH User’s Manual 190
- Embedded fieldbus 191
- 1-188 ACH550-UH User’s Manual 192
- ACH550-UH User’s Manual 1-189 193
- Preferred wiring diagram 194
- Alternate wiring diagram 194
- Communication setup – EFB 195
- 1-192 ACH550-UH User’s Manual 196
- ACH550-UH User’s Manual 1-193 197
- Service 198
- ACH550-UH User’s Manual 1-195 199
- 1-196 ACH550-UH User’s Manual 200
- Miscellaneous driv e control 201
- 1-198 ACH550-UH User’s Manual 202
- ACH550-UH User’s Manual 1-199 203
- Feedback from the drive – EFB 204
- ACH550-UH User’s Manual 1-201 205
- Diagnostics – EFB 206
- ACH550-UH User’s Manual 1-203 207
- 1-204 ACH550-UH User’s Manual 208
- ACH550-UH User’s Manual 1-205 209
- 1-206 ACH550-UH User’s Manual 210
- N2 protocol technical data 211
- 1-208 ACH550-UH User’s Manual 212
- PC-Version 213
- Converter 213
- Panel Version/LTD 213
- N2 binary input objects 214
- N2 analog output objects 215
- FLN protocol technical data 219
- Overview 220
- Drive I/O 221
- Drive Config 221
- Process PID 222
- External PID 222
- ACH550-UH User’s Manual 1-219 223
- ° F - 30° F) x (0.1) 223
- ° F - 30° F) x (0.01) 223
- Point database 224
- ACH550-UH User’s Manual 1-221 225
- 1-222 ACH550-UH User’s Manual 226
- Detailed point descriptions 227
- 1-224 ACH550-UH User’s Manual 228
- ACH550-UH User’s Manual 1-225 229
- 1-226 ACH550-UH User’s Manual 230
- ACH550-UH User’s Manual 1-227 231
- 1-228 ACH550-UH User’s Manual 232
- ACH550-UH User’s Manual 1-229 233
- 1-230 ACH550-UH User’s Manual 234
- ACH550-UH User’s Manual 1-231 235
- 1-232 ACH550-UH User’s Manual 236
- ACH550-UH User’s Manual 1-233 237
- 1-234 ACH550-UH User’s Manual 238
- ACH550-UH User’s Manual 1-235 239
- 1-236 ACH550-UH User’s Manual 240
- ACH550-UH User’s Manual 1-237 241
- Statement 242
- ACH550-UH User’s Manual 1-239 243
- BACnet Object Definitions 244
- ACH550-UH User’s Manual 1-241 245
- 1-242 ACH550-UH User’s Manual 246
- For the 0xxxx registers: 247
- • Status is always readable 247
- 1-244 ACH550-UH User’s Manual 248
- ACH550-UH User’s Manual 1-245 249
- 1-246 ACH550-UH User’s Manual 250
- ACH550-UH User’s Manual 1-247 251
- 1-248 ACH550-UH User’s Manual 252
- ACH550-UH User’s Manual 1-249 253
- ABB drives profile 254
- DCU profile 255
- Status Word 256
- The contents of the 256
- ACH550-UH User’s Manual 1-255 259
- 1-256 ACH550-UH User’s Manual 260
- ACH550-UH User’s Manual 1-257 261
- 1-258 ACH550-UH User’s Manual 262
- ACH550-UH User’s Manual 1-259 263
- 1-260 ACH550-UH User’s Manual 264
- Fieldbus adapter 265
- 1-262 ACH550-UH User’s Manual 266
- ACH550-UH User’s Manual 1-263 267
- Communication setup – FBA 269
- 1-266 ACH550-UH User’s Manual 270
- ACH550-UH User’s Manual 1-267 271
- Feedback from the drive – FBA 272
- Diagnostics – FBA 273
- 1-270 ACH550-UH User’s Manual 274
- ACH550-UH User’s Manual 1-271 275
- 1-272 ACH550-UH User’s Manual 276
- WORD is status 277
- WORD (SW) bits 278
- ACH550-UH User’s Manual 1-275 279
- 1-276 ACH550-UH User’s Manual 280
- ACH550-UH User’s Manual 1-277 281
- 1-278 ACH550-UH User’s Manual 282
- ACH550-UH User’s Manual 1-279 283
- 1-280 ACH550-UH User’s Manual 284
- Diagnostics 285
- Correcting faults 286
- ACH550-UH User’s Manual 1-283 287
- 1-284 ACH550-UH User’s Manual 288
- ACH550-UH User’s Manual 1-285 289
- 1-286 ACH550-UH User’s Manual 290
- ACH550-UH User’s Manual 1-287 291
- Correcting alarms 292
- ACH550-UH User’s Manual 1-289 293
- 1-290 ACH550-UH User’s Manual 294
- Maintenance 295
- Drive module fan replacement 296
- ACH550-UH User’s Manual 1-293 297
- 1-294 ACH550-UH User’s Manual 298
- ACH550-UH User’s Manual 1-295 299
- 1-296 ACH550-UH User’s Manual 300
- ACH550-UH User’s Manual 1-297 301
- Capacitors 302
- Control panel 302
- Technical data 303
- Ratings, 380…480 volt drives 304
- 1-302 ACH550-UH User’s Manual 306
- Input power connections 307
- 208…240 volt, fuses 308
- 380…480 volt, fuses 308
- ACH550-UH User’s Manual 1-305 309
- 1-306 ACH550-UH User’s Manual 310
- ACH550-UH User’s Manual 1-307 311
- 1-308 ACH550-UH User’s Manual 312
- ACH550-UH User’s Manual 1-309 313
- 1-310 ACH550-UH User’s Manual 314
- Motor connections 315
- 1-312 ACH550-UH User’s Manual 316
- ACH550-UH User’s Manual 1-313 317
- 1-314 ACH550-UH User’s Manual 318
- ACH550-UH User’s Manual 1-315 319
- 1-316 ACH550-UH User’s Manual 320
- Control connections 321
- 1-318 ACH550-UH User’s Manual 322
- ACH550-UH User’s Manual 1-319 323
- Efficiency 324
- Air flow, 380…480 volt drives 325
- Dimensions and weights 326
- Mounting dimensions 327
- R1…R6 mounting dimensions 327
- 1-324 ACH550-UH User’s Manual 328
- Outside dimensions – R1…R6 329
- 1-326 ACH550-UH User’s Manual 330
- Degrees of protection 331
- Ambient conditions 332
- Materials 333
- Applicable standards 334
- ACH550-UH User’s Manual 1-331 335
- Liability limits 336
- ACH550-UH User’s Manual 1-333 337
- Numerics 338
Verwandte Produkte und Handbücher für Nein ABB RDNA-01
Nein ABB Tina 7A Wartungshandbuch
(12 Seiten)
(12 Seiten)
Nein ABB FENA-01 Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Nein ABB FPBA-01 Spezifikationen
(21 Seiten)
(21 Seiten)
Nein ABB AW400 Series Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Nein ABB FENA-21 Bedienungsanleitung
(46 Seiten)
(46 Seiten)
Nein ABB RECA-01 Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Nein ABB FDNA-01 Bedienungsanleitung
(460 Seiten)
(460 Seiten)
Nein ABB RDNA-01 Bedienungsanleitung
(330 Seiten)
(330 Seiten)
Nein ABB Tina 7A Wartungshandbuch
(62 Seiten)
(62 Seiten)
Nein ABB RDNA-01 Bedienungsanleitung
(302 Seiten)
(302 Seiten)
Nein ABB Tina 7A Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Nein ABB ML82PH Bedienungsanleitung
(29 Seiten)
(29 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern